Cloudray Ruida RDLC320-A Co2 Laser DSP Controller for Laser Engraving and Cutting Machine

Product Information

G-code post-processor: The post-processor should be able to translate the design files into machine-readable code, and be compatible with various file formats. When the laser is a glass tube, if the used laser is outputted in the low-level form, this pin will be connected with the laser power enable end and used to control the ON/Off of laser. The first section is general configuration, and then there are settings that are specific to each axis, followed by a Laser section, for configuration specific to the laser type. Homing, Directions, and Travel ¶ Exactly!! I typed in 1.2 INCHES for the move and the table moved down 1.2 mm and the display read 1.2. But the display is in inches. see the problem yet? after the 1.2 mm move the display should have read 1.2/25.4=0.0472 Now, the laser power supply has got an in-terminal and at that in-terminal, there is a little network which decodes that signal.

The analog signals for Laser Power. If Glass Tube is used, this pin is recommended to control the power of the Laser. on-board system encryption control, onboard parameter storage, and a maximum file storage capacity of 256M. Hard-spacing Protection: it is used for whether the hard-spacing protection of this axle is enabled. Laser Tube Configuration: single laser and double lasers are available for option and set in accordance with the laser-tube quantity provided by the manufacturer.The next part is figuring out how far the laser moves when you tell it to, and how far off it is. The controller needs to know how far a single step moves when it sends a step pulse to the motors so it can translate real measurements into the proper number of steps. Rough Calibration ¶ It has a number of advanced features, such as support for 3D engraving, nested cutting, and automatic corner optimization. If you need to reset your Ruida Controller to it’s DEFAULT Parameters as defined by your Laser System Manufacturer. This is the procedure to follow:

CO2 laser controller boards play a crucial role in controlling the operation of CO2 laser systems, ensuring optimal performance and precision. These boards act as the central control unit, governing various aspects of the laser system, including laser power, speed, movement, and synchronization.Now, you’ll notice that beside that in-terminal, we’ve already got a five volt, but that’s a five volt output, not a five volt input. Pre-burning Pulse width: when the laser is RF laser and need pre-burning pulse, you can configure the features of pre-burning pulse by pre-burning frequency and pre-burning pulse width. It may not have as many advanced features as some other laser cutting and engraving software programs on the market. LightBurn is a third-party software program that is compatible with Ruida controllers. It provides users with a modern and intuitive interface for designing and executing laser jobs. It also has advanced features such as camera alignment and automatic job optimization. Firmware Upgrade

The Ruida RDC6442S is a motion control system used in laser engraving and cutting machines. It is known for its high-speed and precise control of the laser head, which enables it to cut and engrave a wide range of materials, including wood, acrylic, leather, and metal. The laser machines will be equipped with unique configurations (only for machines on www.cloudraylaser.com) which have high stability and marking efficiency.Signals of the two interfaces are similar and the first digital interface (CN5) is hereby example: Pin Maximum Acceleration: it means the maximum acceleration of the motion axis in accelerated or decelerated motion. If the acceleration is set too large, it will make the motor lose steps, jar and even squeak; if too small, it will cause the reduction of acceleration so as to reduce the running speed of the whole figure. For the axis with larger inertia, such as Y axis corresponding to the beam, its typical setting range is 800~3000mm/s2; for the axis with smaller inertia, such as X axis corresponding to the car, its typical setting range is 8000~20000mm/s2. RDWorks includes a wide range of features and tools for creating and editing designs for laser cutting and engraving, including vector graphics editing, raster image processing, layer management, and cutting and engraving settings. It also includes a preview and simulation function that allows you to see how your design will look and how the laser will move during the cutting or engraving process.