About this deal
Another thing we love to do at LiquidHaus is mixing and matching brands. Sometimes you can get a great synergy between brand aesthetics or even functionality that you simply can’t find when you decide to go with just one brand, especially for watercooling components. The beveled edge also serves as a bottom-front I/O, keeping your desk setup clean and functional. A Better Way to Build
The Hyte Y60 is an interesting PC case that can be the foundation of a stunning build if you play your parts right. If you're looking to show off your components, the Y60 is one of the best chassis you can buy to do just that. If aesthetics is your top priority, it's a no-brainer. The three pre-installed Flow FE12 fans with fluid-dynamic bearings provide whisper-quiet operation. As GPUs have gotten beefier (and let’s face it, more expensive), they’ve also become the star of PC builds. You worked hard to get that GPU, so why wouldn’t you want to show it off?The issue is that the fan is set slightly too close to the rear I/O panel. Many motherboards today have preinstalled rear I/O shields and shrouds, which respectively help ease installation and improve the board's aesthetics. All of the motherboards we had on hand for testing employed this design, and none of them could be installed into the Hyte without first removing the fan. This likely wouldn't be a problem if you used a motherboard with a detached rear I/O shield and no rear shroud, but as essentially all high-end boards nowadays have a rear I/O shroud, it's a fairly significant design flaw. Single tempered glass panels are everywhere - but why limit your view to just one angle? We created a wrap-around glass profile in the Y60, elevating your PC into a functional art piece that can be admired and photographed from nearly any view. Oh, and it’s removable, in case you want to take your liquid cooling mods WAY outside the box ;) With vertical orientation can come some cooling challenges; don’t worry, we thought of that too. Our “cold floor” design uses lateral vents to draw air up from the bottom of your chassis, removing hot spots and allowing more airflow. Panoramic Views
Furthermore, while you can install the motherboard after removing the exhaust fan, if you want to continue using that fan you'll need to install it somewhere else in the case, as it can't be reinstalled if a rear I/O shroud is present. At LiquidHaus, we take pride in doing things differently in attainable ways, with minimal equipment required. There's room at the top of the case to add up to three 120mm fans or up to a 360mm water cooler. An internal fan mounting location beside the motherboard tray can hold two 120mm or 140mm fans or up to a 280mm water cooler.
Continuing our product announcement series for 2022, we think you’re going to love our first ATX PC case, the Y60.
Building a system inside the Hyte Y60 is a mixed bag, with some notable annoyances. A few notable oversights make installing the motherboard more problematic than usual. In particular, we had to remove the preinstalled 120mm fan from the rear of the case before we could install a motherboard.Our build features traditional building techniques, along with a little specialized acrylic work and some classic modding, to achieve a unique look. The vision for the Y60 was to make a chassis that displays everything you want, and hides everything else. You’ve already blown us away with some incredible REVOLT 3 builds and mods. We can’t wait to see the amazing PCs that get built in here! More Specs Hyte says it designed the Y60 with liquid cooling in mind, with the cooler radiator attached to the internal fan mount. This would help to improve airflow significantly, as the water cooler could pull air into the case through the right-side panel. If you opt to use an air cooler, however, Hyte indicates that you'll see higher CPU and GPU temperatures. For that reason, the company recommends that you buy two case fans and install them on the internal fan mount if using an air cooler. You mount the power supply behind the motherboard mounting tray, and this aspect of the building process is smooth sailing. A platform is in place to hold the PSU, with nothing at all to get in the way of inserting it. Conveniently placed cut-outs in the motherboard mounting tray also help with running cables directly where they need to go. The cut-outs are positioned and angled to be out of view when looking through the tempered glass, for a tidier finished build.